For pricing info and quotes:
Toll Free: 800-225-2952  ⚫   E-Mail
Special discounts on pipe plugs are available.

Plumber's Nozzles:

Primary Plumbers' Nozzles include 1/8", 1/4" and 3/8" nozzles. These nozzles are used to clear blockages and flush residential and small commercial lines. They are categorized into three steps and clean most effectively when used in our recommended series.

Primary Plumbers' Nozzles are used to unblock/unclog and restore flow to a line. This is the first nozzle that should be run in a line. Primary Plumbers' Nozzles are the first nozzles used to clean stoppages and blockages within small lines. These nozzles are used to clear blockages and flush residential and small commercial lines. They are for unclean, unchecked, undone pipe and are run quickly through pipes to break blockages.

STEP 1: Primary Plumber's Nozzles:

  • 1/8" Short Nozzle: A general purpose nozzle used for small drains and turns. It can be used in pipe sizes ranging from 2 to 4 inches.

    - Equipped with 6 rear jets at a 25 degree angle.
    - Part# 05-2 (40 degree) | Part# 05-3 (25 degree)
    - Rated for 3-6 gpm up to 4000 psi
    - Can be requested without the forward jet

  • 1/4" Penetrator Nozzle: A bullet style design for greater thrusts to push and penetrate blockages. It can be used in pipe sizes ranging from 2 to 8 inches.

    - Can be equipped with 3 to 6 rear jets at a 15 degree angle.
    - Part# 10-6 (15 degree)
    - Rated for 3-10 gpm up to 4000 psi
    - Can be requested without the forward jet

  • 3/8" Ice Grease Penetrator Nozzle: The 3/8" Ice Grease Penetrator Nozzle by Shamrock is a bullet style nozzle designed for greater thrust and penetration. It is equipped with three forward jets at 5 for powerful thrust through blockages. It can operate in pipe sizes ranging from 2 to 8 inches.

    - Equipped with 3 rear jets at 15 degrees and 3 forward jets at 5 degrees.
    - Part# 15-13 (15 degree)
    - Rated for 3-10 gpm up to 4000 psi
    - Can be requested without the forward jet

  • 3/8" Penetrator Nozzle: The 3/8" Penetrator Nozzle by Shamrock has a bullet style design for greater thrusts to push and penetrate blockages. It can be used in pipe sizes ranging from 2 to 8 inches.

    - Can be equipped with 3 to 6 rear jets.
    - Part# 15-3 (15 degree)
    - Rated for 3-10 gpm up to 4000 psi
    - Can be requested without the forward jet

STEP 2: Secondary Plumbers' Nozzles:


Secondary Plumbers' Nozzles are used to flush out debris loosened from work done with the primary nozzle. Secondary Plumbers' Nozzles are used to get up lines quickly. These nozzles have a wider angle than Primary Plumbers' Nozzles and are designed to flush out the debris from the pipe bottom. They are not designed to clean the entire circumference of the pipe.

  • 1/8" Ball Nozzle: The 1/8" Ball Nozzle by Shamrock is a short nozzle with recessed threads for hard-to-reach places or to negotiate bends, turns and protrusions. Allows for easy retrieval of nozzle and hose. It can be used in pipe sizes ranging from 2 to 8 inches.

    - Can be equipped with 3 to 6 rear jets at a 30 degree angle.
    - Part# 05-7 (30 degree)
    - Please specify GPM and PSI
    - Can be requested without the forward jet

  • 1/8" Short Nozzle: The 1/8" Short Nozzle by Shamrock is a general purpose nozzle used for small drains and turns. It can be used in pipe sizes ranging from 2 to 4 inches.

    - Equipped with 6 rear jets at a 25 degree angle.
    - Part# 05-2 (40 degree) | Part# 05-3 (25 degree)
    - Rated for 3-6 gpm up to 4000 psi
    - Can be requested without the forward jet

  • 1/4" Ball Nozzle: The 1/4" Ball Nozzle by Shamrock is a short nozzle with recessed threads for hard-to-reach places or to negotiate bends, turns and protrusions. Allows for easy retrieval of nozzle and hose. It can be used in pipe sizes ranging from 2 to 8 inches.

    - Can be equipped with 3 to 6 rear jets at a 30 degree angle.
    - Part# 10-7
    - Rated for 3-10 gpm up to 4000 psi
    - Can be requested without the forward jet

  • 3/8" Ball Nozzle: The 3/8" Ball Nozzle by Shamrock is a short nozzle with recessed threads for hard-to-reach places or to negotiate bends, turns and protrusions. Allows for easy retrieval of nozzle and hose. It can be used in pipe sizes ranging from 2 to 8 inches.

    - Can be equipped with 3 to 6 rear jets at a 30 degree angle.
    - Part# 15-7
    - Please specify GPM and PSI
    - Can be requested without the forward jet

STEP 3: Tertiary Plumbers' Nozzles:


Tertiary Plumbers' Nozzles include cleaning and rotating nozzles. They are designed to clean the entire circumference of the pipe and should be used after running a Primary Plumbers' Nozzle and a Secondary Plumbers' Nozzle.

  • 1/8" Ball Nozzle: The 1/8" Ball Nozzle by Shamrock is a short nozzle with recessed threads for hard-to-reach places or to negotiate bends, turns and protrusions. Allows for easy retrieval of nozzle and hose. It can be used in pipe sizes ranging from 2 to 8 inches.

    - Can be equipped with 3 to 6 rear jets at a 30 degree angle.
    - Part# 05-7 (30 degree)
    - Please specify GPM and PSI
    - Can be requested without the forward jet

  • 1/4" Ball Nozzle: The 1/4" Ball Nozzle by Shamrock is a short nozzle with recessed threads for hard-to-reach places or to negotiate bends, turns and protrusions. Allows for easy retrieval of nozzle and hose. It can be used in pipe sizes ranging from 2 to 8 inches.

    - Can be equipped with 3 to 6 rear jets at a 30 degree angle.
    - Part# 10-7
    - Rated for 3-10 gpm up to 4000 psi
    - Can be requested without the forward jet

  • 3/8" Ball Nozzle: The 3/8" Ball Nozzle by Shamrock is a short nozzle with recessed threads for hard-to-reach places or to negotiate bends, turns and protrusions. Allows for easy retrieval of nozzle and hose. It can be used in pipe sizes ranging from 2 to 8 inches.

    - Can be equipped with 3 to 6 rear jets at a 30 degree angle.
    - Part# 15-7
    - Please specify GPM and PSI
    - Can be requested without the forward jet

  • 3/8" button nozzle: The 3/8" Button Nozzle by Shamrock is a general purpose flushing nozzle designed for turns and bends in sanitary lines. It can be used in pipe sizes ranging from 2 to 4 inches.

    - Can be equipped with 3 to 6 rear jets at a 40 degree angle.
    - Part# 15-2 (40 degree)
    - Rated for 3-10 gpm up to 4000 psi
    - Can be requested without the forward jet

  • 1/4" rotator: The 1/4" Rotator Nozzle by Shamrock completely cleans pipes, freeing grease, roots and fibers. This nozzle is a must have for contractors with regular maintenance contracts. The 1/4" Rotator Nozzle can be used in pipe sizes ranging from 2 to 6 inches.

    - Can be equipped with 2 or 3 rear jets at a 15 degree angle
    - Part# RR-4
    - *The minimum flow rate needed for this nozzle to rotate properly is 4 gpm.
    - Please specify GPM and PSI

  • 3/8" rotator: The 3/8" Rotator Nozzle by Shamrock completely cleans pipes, freeing grease, roots and fibers. This nozzle is a must have for contractors with regular maintenance contracts. The 3/8" Rotator Nozzle can be used in pipe sizes ranging from 2 to 8 inches.

    - Can be equipped with 2 or 3 rear jets at a 15 degree angle
    - Part# RR-6
    - *The minimum flow rate needed for this nozzle to rotate properly is 4 gpm.
    - Please specify GPM and PSI

Related Products:


Piranha Sewer Cleaning Hose

Click pic for more info...


Jet Power: Sewer Line Degreaser

Click pic for more info...